USER’S MANUALModel No. WECCSY29830Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONR
1013. Slide six Weights (41) onto the Right WeightGuides (26). Make sure the Weights are turnedso the pin grooves are on the bottom.Press a Weight Tub
1182822928 67 8909092262747589285788235151638298290929015. Press a 2” Square Inner Cap (67) into the CenterTop Frame (8). Place the Center Top Frame
1220. See the inset drawing. Press a Plastic Bushing(60) onto each welded tube on the Press Frame(17). Slide the Press Frame into place on thePress Ba
132377208473Bracket2441059073373422. Identify the Right and Left Butterfly Arms (19, 20)by the positions of the welded brackets.Press a 1 3/4” Square
1426. Remove another “V”-Pulley (34) from the baglabeled “PULLEY BAG 2.”Wrap the Butterfly Cable (73) around the “V”-Pulley (34) in the direction show
32. Identify the Ab Cable (74).It is approximately226 1/2” long, and it has a ball on one end andan eyelet on the other.Wrap the Ab Cable (74) around
1634. Wrap the Ab Cable (74) around a 3 1/2” Pulley(35) in the direction shown. Attach the Pulley tothe Double “U”-Bracket (31) with a 3/8” x 1 3/4”Bo
1738933274353838. Wrap the Ab Cable (74) around a 3 1/2” Pulley(35) in the direction shown. Attach the Pulley anda Cable Trap (38) to the forth set of
1841. Locate the Weight Plate (48) that is attachedto the bottom of the Bottom Weight (47).See the inset drawing.Attach the end of the AbCable (74) to
1945. Remove the 3/8” Nylon Jamnut (92) from the 3/8” x 4 3/4” Bolt (102) inserted into the ButterflyUpright (4) in step 43.Wrap the Low Cable (71) ar
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2049. Wrap the Press Cable (72) around a 3 1/2” Pulley(35) in the direction shown. Attach the Pulley anda Cable Trap (38) to the indicated hole in the
2153. Wrap the Press Cable (72) around a 3 1/2” Pulley(35) in the direction shown. Attach the Pulley anda Cable Trap (38) to the indicated hole on the
2257. Remove the 3/8” Nylon Jamnut (92) used in step53. Route the Press Cable (72) through the PressFrame (17).Wrap the Press Cable (72) around a 3 1/
2361. Attach the Press Cable (72) to the remaining “U”-Bracket (33) with a 1/4” Washer (99) and a 1/4”Nylon Locknut (103). Note: Do not completelytigh
2465. Press a 1 3/4” Square Inner Cap (68) into theindicated end of the Adjustment Tube (15).Attach the Adjustment Tube (15) to the bracket(not visibl
25ADJUSTING THE LEG PRESS PLATETo adjust the position of the Leg Press Plate (16), pullout the Adjustment Pin (40) and slide the AdjustmentTube (15) e
2681474141CHANGING THE WEIGHT SETTINGTo change the setting of a weight stack, insert aWeight Pin (81) under the desired Weight (41). Insertthe Weight
27WEIGHT RESISTANCE CHARTThe chart below shows the approximate weight resistance at each exercise station. “Left Top” and “Right Top”refer to the 6 lb
28The threaded ends on the Rear Cable (70) and thePress Cable (72) attached to the weight stacks canbe used to tighten the cables. To tighten the Rear
2997127210434909757285349037Slack can be removed from the Press Cable (72) bymoving the “V”-Pulley (34) attached to the Press SeatFrame (12) closer to
3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.1. Read al
CABLE DIAGRAMSThe Cable Diagrams below and on the next page show the proper routing of the Rear Cable (70), the Low Cable(71), the Press Cable (72), t
Low Cable (71)54312673189101156214124323Butterfly Cable (73)5Rear Cable (70)314Ab Cable (74)
Part No. 197804 R1103A Printed in Canada © 2003 ICON OF/DU CANADA, INC.ORDERING REPLACEMENT PARTSTo order replacement parts, call toll-free 1-888-936-
Note: Assembly is divided into four stages: 1) frame assembly; 2) armassembly; 3) cable assembly; and 4) seat assembly. The hardware foreach assembly
1” Retainer (54)1" Cover Cap (55)1" Square Inner Cap (69)1 3/4" Square Inner Cap (68)Round Inner Cap (63)3/4" Round Inner Cap (64)
3/8" Nylon Locknut (90)3/8" Nylon Jamnut (92)1/4" x 2 1/2" Carriage Bolt (91)5/16" x 2 1/2" Carriage Bolt (75)3/8"
3/8" x 3 1/2" Carriage Bolt (95)5/16" x 1" Shoulder Bolt (84)5/16" x 2 3/4" Shoulder Bolt (108)3/8" x 3 1/2" B
81REMOVE THIS PART LIST/EXPLODED DRAWINGFROM THE MANUAL.SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 Butterfly Base2 1 Center Base31 Press Base4 1 But
625962625635383835353835353837341818603538383232231234373838383814403535616110950151647414127462646424445333517911029383510932323835353836362828834343
4ASSEMBLED DIMENSIONS: Height: 195.58 cm (77 in.)Width: 203.2 cm (80 in.)Depth: 139.7 cm (55 in.)Low PulleyStationFoot PlateLeg LeverPress ArmBackrest
5Make sure you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mallet• You will
1. Before beginning, be sure that you have readand understood the information on page 5.Locate and open the parts bag labeled“FRAME ASSEMBLY.”Press a
4. Slide the Butterfly Upright (4) over the indicated5/16” x 2 1/2” Carriage Bolts (75) in the ButterflyBase (1). Hand tighten two 5/16” NylonLocknuts
78. Press a 1” Square Inner Cap (69) into the smalltube on the Press Upright (5).Slide the Press Upright (5) over the indicated5/16” x 2 1/2” Carriag
910. Press a 2” Square Inner Cap (67) into the PressTop Frame (9). Attach the Press Top Frame (9) to the indicatedbracket at the top of the Press Upri
Commentaires sur ces manuels