USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
ARM ASSEMBLYFRAME ASSEMBLY8. Attach the Top Frame (55) to the WeightGuides (62) using a 5/16” x 6” Bolt (60), two1/2” x 1/2” Spacers (61), and a 5/16”
11ARM ASSEMBLY11. Attach the Seat Plate (37) to the Seat Frame(36) using a 1/4” x 2 1/4” Carriage Bolt (38), a1/4” Flat Washer (78), and a 1/4” NylonL
18154847BracketLubricate5565684544471617CABLE ASSEMBLY ARM ASSEMBLY1215. Press a 1 3/4” Square Inner Cap (44) into thelower end of the Left Arm (47).
19. Route the Short Cable (23) around two “V”-Pulleys (6). Attach the “V”-Pulleys and twoLong Cable Traps (50) to the Left Arm (47)and the Right Arm (
2623242523. Important: As you assemble the LongCable (69) in steps 23–30, refer to theCable Diagram on page 21.Route the Long Cable (69) between the B
27. Route the Long Cable (69) behind the PressFrame (17) and under the Seat Frame (36) asshown. Route the Long Cable (69) aroundtwo 3 1/2” Pulleys (15
31. Attach the Seat (13) to the Seat Frame (36)using two 1/4” x 3/4” Bolts (18), a 1/4” x 2 1/4”Bolt (33), and a 1/4” Flat Washer (78).32. Attach the
35. Attach the Shroud (59) to the brackets on theTop Frame (55) and the Base (4) using four#8 x 1/2” Screws (79).173579795955794SEAT ASSEMBLY36. Make
1854395352232526CHANGING THE WEIGHT SETTINGTo change the weight setting of the weight stack,insert the Weight Pin (26) under the desired Weight(25). B
19This chart shows the approximate weight resistance at each exercise station. “Top” refers to the 6.5 lb. topweight. The other numbers refer to the 1
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. Thetrainin
21CABLE DIAGRAMThe diagram below shows the proper routing of the Short Cable (23) and the Long Cable (69). Use the diagramto be sure that the cables a
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY19001 R0201AKey No. Qty. Desc
221661564921218432168654842454479797979361626023865756632625731473521581515125814332121211919771227532121151716523922315754646314944343028293231494434
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
31. Read all instructions in this manual and inthe accompanying literature before using thetraining system. 2. It is the responsibility of the owner t
4BEFORE YOU BEGINFoot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButterfly ArmCurl PadCurl FramePress ArmWeight StackBackrestShroudSeat
1/4" Nylon Locknut (2)1/2" x 1/2" Spacer (61)1/4" Flat Washer (78)5/16" Flat Washer (70)5/8" x 1/2" Spacer (82)3/8&
1/4" x 2 1/4" Carriage Bolt (38)5/16" x 6" Bolt (60)3/8" x 5" Bolt (75)3/8" x 4 1/4" Bolt (64)3/8" x 4&qu
7ASSEMBLYMake sure you have the following tools:• Two (2) adjustable wrenches• One (1) standard screwdriver• One (1) phillips screwdriver• One (1)
34FRAME ASSEMBLY81214241925PinGroove623. Attach the Front Upright (42) to the Base (4)using two 3/8” x 2 1/4” Bolts (1) and two 3/8”Nylon Locknuts (21
5. Insert the Weight Tube Cap (72) into the indi-cated end of the Weight Tube (63). Slide theWeight Tube into the center holes in theWeights (25). Sli
Commentaires sur ces manuels