USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find that there
18152312201566685048671617CABLE ASSEMBLY1015. Route the Long Cable (23) around the “V”-Pulley (6) on the Right Arm (48). Be surethat the Cable is in t
19. Assembly steps 19 through 21 show howto complete the assembly of several pre-attached parts.The 5/8” x 9/16” Spacer (73) has been pre-attached on
2522232422. Locate the Medium Cable (58). Route theMedium Cable (58) under the 3 1/2” Pulley(15) attached to the lower hole in the PressFrame (17). Be
26. Attach the end of the Medium Cable (58) tothe Long “U”-Bracket (57) with a 1/4” NylonLocknut (2) and a 1/4” Flat Washer (10). Donot completely tig
29. Press a 1 1/2” Square Inner Cap (32) into theSeat Frame (36).Insert the 1/4” x 2” Carriage Bolt (38) into thecenter hole in the Seat Plate (37). A
33. Press 3/4” Round Inner Caps (34) into theends of both 12 1/2” Pad Tubes (28). Insert one 12 1/2” Pad Tube (28) into theSeat Frame (36). Slide a 5
36. Press 1 1/2” Square Inner Caps (32) into theends of the Left VKR Arm (79) and the RightVKR Arm (80). Press 1” Round Inner Caps(49) into the ends o
1738. Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the loca-tions shown in the illustration below.39. M
1854395352232526543952535853CHANGING THE WEIGHT SETTINGTo change the weight setting of the weight stack,insert the Weight Pin (26) under the desired W
19ATTACHING AND REMOVING THE SEATSet the bracket on the Seat Frame (36) on the indi-cated pins on the Front Upright (42). Attach the SeatFrame to the
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each exercise station. “Top” refers to the 6.5 lb. topweight. The other
21TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy
22CABLE DIAGRAMThe diagram below shows the proper routing of the Short Cable (35), the Medium Cable (58), and the LongCable (23). Use the diagram to b
23NOTES
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-225-0653, Mondaythrough Friday, 6
Please Note: The assembly is divided into five stages: 1) frame assembly, 2) press and butterflyarm assembly, 3) cable and pulley assembly, 4) seat an
1 1/2" Square Inner Cap (32)–51 3/4" Square Inner Cap (44)–62" Square Inner Cap (27)–22" Square Outer Cap (51)–21" x 7/8"
1" Round Inner Cap (49)–105/16"Nylon Locknut (3)–231/4" Flat Washer (10)–125/16" Flat Washer (8)–81" Round Cover Cap (70)–23/
81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY95100 R1295AKey No. Qty. Desc
31. Read all instructions in this manual and inthe accompanying literature before using thehome gym system. 2. It is the responsibility of the owner t
231111885527121544157123214421361603355114192651256463376729213341276515714110433216507427506216970697047484445444552533949622106766741268553216615207
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 74 in.Width: 40 in. Length: 58 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverVerti
1High Sideof Bracket5151413Slotted Hole38561131427511. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box
23FRAME ASSEMBLY6494933883878115614116542114427334442Crossbar565549882. Slide the Front Upright (42) onto the 5/16” x2 1/2” Carriage Bolts (1) in the
5. Press the Weight Tube Bumper (64) into theend of the Weight Tube (63). Insert theWeight Tube into the stack of Weights (25).Be sure that the pins o
ARM ASSEMBLY8. Wet the handle of one Press Arm (46) withsoapy water. Slide a Hand Grip (31) onto thehandle. Press a 1” Round Inner Cap (49) intothe ot
9CABLE ASSEMBLY11. During steps 11 through 27, refer to theCABLE DIAGRAM on page 22 of this manualto verify proper cable routing. Before begin-ning th
Commentaires sur ces manuels